Tag Archives: integrity_toys

Bratz Pixiez Reroot notes and How I reroot hard heads

Some photos from working on the bratz pixiez:

  1. deciding on a widows peak and giving the face a heart shape by bringing the hair down at the ears.
  2. the nerve wracking moment when you put in new plugs across the forehead.
  3. mspainted hair plans for the client’s consideration based on prototype photos from toyfair and these that showed up on flickr at just the right time!

How I reroot v hard heads (aka harder than Integrity Toys). (For experienced rerooters)

The difficulties are that you get about 4 minutes at a time where the head is soft enough to work with and that the head needs to be heated without frazzling the hair if you’re using saran. [ By ultra hard heads, I mean the type that give you five minutes of pliability even straight after boiling!]

You’ll need:

  • pin vise for tool method. With a nail or something solid inside the pin vise for the needle to press against.
  • foam block to place the head on while working
  • heat pad set to high heat
  • !timer!
  • no doll grade kanekalon as the frazzle temperature is too low.
  • crocodile clips

The biggest challenge, I guess, is the double tedium of having to wait for the head to heat every four minutes and then getting into the ‘groove’ of working only to have to stop because the head became unworkable again. Do not give in to the temptation to keep working, the plastic does not respond well and can leave big holes or risk cracking open. Vinyl needs some pliability when rerooting.

When heating the head, wrap the hair as low to the roots as possible in a tissue or piece of cotton then put on the timer for 3-5 minutes depending on how hot the heat pad is. You need the head to get hot enough to work but that heat is slightly too much for the saran fibre if you go over 5 mins!

Since your time is limited, make sure that you seperate out lots of wads of hair with crocodile clips so that you can quickly grab them when you run out.
Keep it all in small amounts, brushed and secured with clips etc as you’ll be moving more than usual and that means more risks for messing up hair piles!

Draw out your rerooting lines in pencil on the head in advance to not use up “reroot time” eyeballing and calculating.
Take extra care with front lines, part lines and vunerable areas on the head (take photos before beginning the reroot of any problem zones) as the head is a lot less forgiving.

Have something to do during the heating times and budget double the time of a normal reroot (though it’ll probably be 150-175% unless you’re planning something unusual).

I recommend Nylon over Saran for ultra hard heads as the melt temperature is higher for Nylon which gives you more leeway. Doll grade kanekalon frazzles if you do a boil perm slightly too soon after the boil so I definitely don’t recommend that.

Review: Integrity Toys – Janay and Friends heads

Bought 3 Janays and 1 Alysa for $6 each plus $4 postage from Ebay seller:  MushroomStreet.

The heads are barbie sized, made of hard vinyl and came with their head anchor still inside the head.
(tip: use a hairdryer and grab with pliers to gently ease it out)
 photo janayc_a.jpg
 photo janayo_a.jpg
 photo alysa_a.jpg
 photo janay_curls.jpg
The ears are not pierced but there is a place marker for an ear hole, heads are marked “integrity 2001” on the neck. Neck hole is standard barbie size.
The faces are gorgeously sculpted with slight matte texture to the face that looks and photographs like real skin.
The eyebrows have hair detail and the blushing is very nicely blended.

The hair, however, is terrible: unbrushable nylon, very thick in each plug but thinly rooted across the scalp.
 photo itjanayrooting.jpg

I removed the hair from 3 of the 4 dolls but I’m unsure if they’ll be re-rootable due to the large holes in their heads. Head circumference is 3 inches (wig size 3).
 photo bald_janayo.jpg
 photo bald_alysa.jpg
 photo bald_janayc.jpg

Head holes:
 photo bald_janayo1.jpg
 photo bald_janayc3.jpg
 photo bald_alysa_hole.jpg

Finished result:
 photo janays.jpg